Tag Archives: Aprilia News

Learner legal Aprilia Tuareg 660 L confirmed for July

2022 Aprilia Tuareg 660 L (LAMS)


Aprilia Australia have just confirmed that we’ll be receiving a LAMS variant of the Tuareg 660 – the Tuareg 660 L in July of 2022, following the May/June arrival of the full power version.

2022 Aprilia Tuareg 660 L
2022 Aprilia Tuareg 660 L

The Tuareg 660 L is expected in all three colours, with pricing to be announced closer to the release date. This  move means Aprilia will be offering Australian riders the most advanced adventure machine for new riders available in the country.

2022 Aprilia Tuareg 660 L
2022 Aprilia Tuareg 660 L

The LAMS version is retuned to 35 kW, in other words meeting European A2 restricted requirements, with that power peaking at 5500 rpm and 61 Nm of torque available at 5000 rpm. That’s down from the full power version at 58.8 kW (at 9250 rpm), with torque softened by a more reasonable 9 Nm.

The good news is of course that the Tuareg 660 L otherwise shares the same specifications of the full power version, which is an impressive loadout.

In the Tuareg 660 L power is restricted to 35 kW
In the Tuareg 660 L power is restricted to 35 kW

The 659 cc twin-cylinder features a 270-degree firing order and model-specific exhaust system, plus tune, with final gearing shorter than seen on the RS 660 from which the engine is derived. A taller sump is also run for ground clearance, with other changes over the roadster machines being a new rose pipe and intake mouth and new oil circuit channel.

The frame is a steel tube design with cast plates and welded-on sub-frame allowing for 210 kg in total load capacity, with the bike weighing in at 204 kg at the kerb or 187 kg dry. A long swingarm is also run for traction and stability, with pivots in the frame.

The same chassis as in the full power version is run
The same chassis as in the full power version is run

Kayaba provide the suspenders, with 43 mm forks with 240 mm of travel and full adjustability, spec’s matched by the rear shock for both adjustability and travel.

A proper adventure set of wheels are also fitted, with a 21 x 2.50 inch front and 18 x 4.50 inch rear, in 90/90 and 150/70 tyres, which will be Pirelli Scorpion Rally STR units, and the rums are tubeless aluminium as well.

Wheels are a 21/18 inch combo, with Pirelli
Wheels are a 21/18 inch combo, with Pirelli Scorpion Rally STR tyres and Brembo brakes

Brembo provide the braking system, with dual 300 mm rotors and a more modest set of dual-piston calipers run, no doubt with off-road riding in mind. On the rear is a 260 mm rotor with single-piston caliper in comparison. ABS includes off-road mode to disable rear ABS, while the front can also be disabled, with ABS modes linked to ride modes.

A 5 inch TFT is also run with the APRC electronics package
A 5 inch TFT is also run with the APRC electronics package

The Tuareg 660 L will run an extensive electronics system in the form of the APRC package, with Aprilia Traction Control, Aprilia Cruise Control, Aprilia Engine Brake, Aprilia Engine Map and ride modes. Ride modes are split into two road options, an off-road option and a fully customisable mode. Those are Urban, Explore, Off-Road and Individual.

Switchblocks ensure easy control of the TFT and APRC settings

A 5 inch TFT keeps the rider informed, with switches providing easy control of the various settings. The Aprilia MIA system is an accessory however, as is a quick shifter.

Lighting is all LED on the Tuareg 660

Fuel capacity is a generous 18 L, which should be good for just over 400 km in ideal conditions, with a 4 L / 100 km claimed figure. Lighting is full LED, with seat height at 860 mm.

An 18 L fuel tank offers plenty of range on the Tuareg 660

Final drive is chain, while there’s also a slipper clutch fitted, and the three colour options will be Indaco Tagelmust, Martian Red and Acid Gold.

Seat height is 860 mm, with a narrow front of seat that swells out for comfort further back
Seat height is 860 mm, with a narrow front of seat that swells out for comfort further back

We’ll have to wait and see where that pricing lands for now, with the full power 2022 Aprilia Tuareg 660 arriving in May/June, and the 2022 Aprilia Tuareg 660 L due in dealers in July.

2022 Aprilia Tuareg 660 L
2022 Aprilia Tuareg 660 L

2022 Aprilia Tuareg 660 L specifications

2022 Aprilia Tuareg 660 L specifications
Engine type Aprilia forward-facing twin-cylinder, 4-stroke, liquid cooled, dual overhead cam (DOHC) with silent chain drive on the right side, four valve per cylinder.
Bore x stroke 81 x 63.93 mm
Engine capacity 659 cc
Compression ratio 13.5:1
Maximum power 35 kW (47.6 hp) at 5500 rpm 
Maximum torque 61 Nm at 5000 rpm 
Fuel system 2x 48 mm throttle bodies, Ride-by-wire management
Ignition Electric 
Lubrication Wet sump 
Transmission Six-speed, Aprilia Quick Shift (AQS) System up and down available as accessory
Clutch Multiplate wet clutch with slipper system
Secondary drive Chain, drive ratio 15/42 
Electronics APRC Suite that includes ATC (traction control), AEB (engine brake) AEM (engine maps), ACC (cruise control), Four riding modes (Urban, Explore, Off-road, Individual)
Chassis Frame in steel tubing and built-in subframe screwed aluminium plates connecting the frame to the engine
Front suspension Fully adjustable 43 mm upside-down Kayaba fork with counterspring. Wheel travel: 240 mm
Rear suspension Aluminium swingarm. Progressive linkage. Fully adjustable Kayaba monoshock. Wheel travel: 240 mm
Front brake ABS, 300 mm double disc, Brembo callipers with 4 horizontally opposed Æ 30/32 mm pistons. Axial pump and metal braided brake line
Rear brake 260 mm diameter disc; Brembo single piston Æ 34 mm floating calliper. Master cylinder with separate reservoir and metal braided hose, Multimap ABS
Wheels Spoked with aluminium drop centre Front: 2.15×21-inch, Rear: 4.25×18-inch
Tyres Tubeless, Front: 90/90-21, Rear: 150/70 R 18
Dimensions
Wheelbase 1525 mm 
Length 2220 mm 
Width 965 mm
Saddle height 860 mm 
Headstock angle 26.7 degrees
Trail 113.3 mm
Weight 204 kg kerb weight (187 kg dry weight) 
Emissions Euro 5 
Consumption 4.0 litres/100 km 
Fuel capacity 18 litres (inc. 3-litre reserve)
Colour range Indaco Tagelmust, Martian Red, Acid Gold

Source: MCNews.com.au

Aprilia Tuareg 660 on the way in 2022

2022 Aprilia Tuareg 660


Aprilia’s Tuareg 660 will hit dealer floors next year, with the manufacturer introducing an adventure offering that looks pretty hard-nosed and is built around the 660 powerplant already seen in the RS 660 and Tuono 660 machines.

The 2022 Aprilia Tuareg 660 looks set to sit somewhere in the segment between a T7 and an 890 Adventure R

In some ways the Tuareg 660 could be considered a competitor for the Tenere 700, although being an Aprilia the fairly extensive APRC package adds a host of rider aids, with pricing also expected to push up as a result of what’s on offer.

We’ll have to wait for Australian Tuareg 660 pricing, with a May/June arrival date in 2022

Australian pricing hasn’t been released at this stage, with a May or June release date, but based on the US pricing that is available, the Tuareg 660 sits squarely between the Tenere 700 on price and the 890 Adventure R – although obviously Australian pricing isn’t always a direct reflection of what we see elsewhere.

The Tuareg 660 is based on the 659 parallel twin first seen on the RS 660 and Tuono 660

The ‘660’ or 659 cc powerplant is the DOHC four-stroke twin-cylinder with 270 degree firing order from the previously mentioned models, but producing a more modest 80 horsepower and 70 Nm of torque. Down 20 hp and up 3 Nm from the RS 660 for comparison.

A new high exhaust system is featured in keeping with the ADV theme

Specific to the Tuareg is a new exhaust system, optimising low to mid-range performance, including an ignition advance management algorithm specifically for this model.

Final gearing is also shorter, running a 15 tooth front sprocket, two down on the RS 660, ensuring maximum drive from down low, while a new oil sump sits higher ensuring 240 mm of ground clearance.

Power is 80 hp with gearing also lower than the roadster 660s

Further tweaks were made ensuring adequate lubrication under any conditions with a new rose pipe and intake mouth, with new oil circuit channel in the semi-crankcase to prevent stagnation in the gearbox. In other words tweaks designed for a bike that might see more heavy duty off-road use and the accompanying greater range of conditions that ensues.

A different sump and increased lubrication were a focus on the Tuareg 660 with more extreme conditions obviously envisaged

The Tuareg 660 chassis also receives attention in various ways, with a new high resistance steel tube design with cast plates and the sub-frame is welded to the main unit to allow for a 210 kg load capacity in total, with double the frame anchor points to the engine, compared to the RS 660. As such as the bike uses the engine as a stressed element, with the cylinder bank more vertical for boosted agility in tight turns.

The engine is also used as a stressed member in the Tuareg with six anchor points

The aluminium swingarm is also longer for traction and stability, and pivots in the frame and engine, while running a progressive linkage to the rear Kayaba shock. The Kayaba system, front and rear, offers 240 mm of travel and is fully adjustable, with rebound, compression and preload, with the latter on the shock a convenient preload handle.

A longer aluminium swingarm boosts stability, with Brembo providing the stoppers

The 18 L fuel tank is also kept narrow where the rider grips it and is protected by the frame, with weight centralisation and the CoG a concern, along with ensuring fuel is accessible even in the steepest conditions.

Spoked wheels are run with Pirelli rubber and the front brakes are 300 mm rotors with dual-piston Brembo calipers

Wheel and tyre options are obviously very important, especially as we’re talking a ‘proper’ adventure machine, not just a tourer with some dual purpose tyres and we’re seeing a 2.50 x 21 inch front and 4.50 x 18 inch rear, which will be clad in Pirelli Scorpion Rally STR tyres in a 90/90 and 150/70 as standard fitment. Those are tubeless aluminium rims too.

Kayaba provide the fully adjustable long travel suspension

Brembo provides a top notch braking system with an obvious off-road bent, running dual 300 mm front rotors and dual-piston calipers, while the rear is a 260 mm unit with single-piston caliper. ABS is also fitted, linked to the ride modes, with various levels of intervention including off-road which disables the rear and allows the front to be disabled too.

The Tuareg 660 runs the APRC electronics package and a 5 inch TFT

Naturally as an Aprilia, the APRC system makes an appearance, offering a host of rider aids, with ATC – Aprilia Traction Control; ACC – Aprilia Cruise Control; AEB – Aprilia Engine Brake; and AEM – Aprilia Engine Map. The AEB basically controls off-throttle response and AEM or modes differs the throttle response without changing peak performance.

Two road orientated ride modes, an off-road mode and a fully customisable mode are on offer

Ride modes include two road specific options, an off-road option and a fully customisable option, those are Urban and Explore, Off-Road and Individual for the custom mode, which is fairly self explanatory. Urban is calibrated for maximum electronic intervention.

Aprilia Tuareg 660 stock one-piece seat

Aprilia promise intuitive switches, with the right side allowing easy mode selection, which with presents should largely negate the need to switch through individual settings on the run.

2022 Aprilia Tuareg 660

A 5 inch TFT meanwhile offers a clear view of what mode you’re in, speed and other important information. The Aprilia MIA or multimedia platform is an accessory, which can sync with a smartphone and save completed trip data, including geo-referenced telemetry, while a quick shift is also an accessory rather than standard fitment.

2022 Aprilia Tuareg 660

The wet weight figure, or kerb figure claimed by Aprilia is also 204 kg, or 187 kg dry, and aligns closely with the official Tenere 700 figure as a point of comparison, with seat height 860 mm and the 18 L fuel tank accompanied by a 4 L/100 km consumption figure, giving the Tuareg 660 an easy 400 km range starting to dip into the 3 L reserve with some room to play. Lighting is also all LED.

2022 Aprilia Tuareg 660

Colour options are the Martian Red or Acid Gold, with Indaco Tagelmust, as shown in the pictures carrying a premium in other markets and certainly standing out. The 2022 Aprilia Tuareg 660 is expected to arrive in Australian dealers in May or June of 2022, however we haven’t got local pricing at this stage.

2022 Aprilia Tuareg 660

2022 Aprilia Tuareg 660 specifications

2022 Aprilia Tuareg 660 specifications
Engine type Aprilia forward-facing twin-cylinder, 4-stroke, liquid cooled, dual overhead cam (DOHC) with silent chain drive on the right side, four valve per cylinder.
Bore x stroke 81 x 63.93 mm
Engine capacity 659 cc
Compression ratio 13.5:1
Maximum power 80 hp (58.8 kW) at 9250 rpm 
Maximum torque 70 Nm (7.13 kgm) at 6500 rpm 
Fuel system 2x 48 mm throttle bodies, Ride-by-wire management
Ignition Electric 
Lubrication Wet sump 
Transmission Six-speed, Aprilia Quick Shift (AQS) System up and down available as accessory
Clutch Multiplate wet clutch with slipper system
Secondary drive Chain, drive ratio 15/42 
Electronics APRC Suite that includes ATC (traction control), AEB (engine brake) AEM (engine maps), ACC (cruise control), Four riding modes (Urban, Explore, Off-road, Individual)
Chassis Frame in steel tubing and built-in subframe screwed aluminium plates connecting the frame to the engine
Front suspension Fully adjustable 43 mm upside-down Kayaba fork with counterspring. Wheel travel: 240 mm
Rear suspension Aluminium swingarm. Progressive linkage. Fully adjustable Kayaba monoshock. Wheel travel: 240 mm
Front brake ABS, 300 mm double disc, Brembo callipers with 4 horizontally opposed Æ 30/32 mm pistons. Axial pump and metal braided brake line
Rear brake 260 mm diameter disc; Brembo single piston Æ 34 mm floating calliper. Master cylinder with separate reservoir and metal braided hose, Multimap ABS
Wheels Spoked with aluminium drop centre Front: 2.15×21-inch, Rear: 4.25×18-inch
Tyres Tubeless, Front: 90/90-21, Rear: 150/70 R 18
Dimensions
Wheelbase 1525 mm 
Length 2220 mm 
Width 965 mm
Saddle height 860 mm 
Headstock angle 26.7 degrees
Trail 113.3 mm
Weight 204 kg kerb weight (187 kg dry weight) 
Emissions Euro 5 
Consumption 4.0 litres/100 km 
Fuel capacity 18 litres (inc. 3-litre reserve)
Colour range Indaco Tagelmust, Martian Red, Acid Gold

2022 Aprilia Tuareg 660 Gallery

Source: MCNews.com.au

Aprilia add Tuono 660 ‘Factory’ edition in 2022

2022 Aprilia Tuono 660 Factory


The Aprilia Tuono 660 will be available in two flavours for 2022, the standard and a new ‘Factory’ version, offering a more comprehensive list of features, as is always the case with an Aprilia machine carrying the ‘Factory’ moniker.

Aprilia’s Tuono 660 gets a Factory edition in 2022

That means a number of up-spec features for the middle-weight Tuono, although this seems to be a case of delivering an RS 660 in the Tuono’s clothes. The Tuono 660 lacks various features seen on the standard RS 660 by way of comparison – reflected in the price difference between models, with the Factory model then returning these to the bike to make for an up-spec Tuono 660.

The 2022 Aprilia Tuono 660 Factory will now match the RS 660 on specification

The Tuono 660 Factory will be lighter, more powerful and boast a higher level of specification.

That starts with running the 660 cc parallel twin in the RS 660 state of tune, bumping power back up to 100 hp, from the 95 you receive on a standard Tuono 660. The Factory also runs one less tooth on the front sprocket to sharpen up acceleration.

Details include boosted power to 100 hp and a lighter battery

Torque remains unchanged at 67 Nm at 8500 rpm, with 80 per cent available from just 4000 rpm. Weight savings in comparison were a simple matter of adding a lithium battery, saving 2 kg and bringing the kerb weight down to 181 kg in total. The changes see the Tuono 660 Factory up 5 hp and down 2 kg.

The Tuono 660 only offers rebound and pre-load in a single leg, however the Factory version will be fully adjustable, with rebound, compression and prel-oad adjustability, as seen on the RS 660.

The Factory gets the full adjustable fork

It’s a similar story with the rear shock, with a Sachs unit to offer compression, rebound and pre-load adjustment, where the standard Tuono only gets rebound and pre-load.

The Sachs shock likewise is fully adjustable

The Tuono 660 Factory also runs the full APRC electronics suite, where the standard Tuono misses out on the IMU – which can be added as an option. As a result the Tuono will offer multi-map cornering ABS, in-line with the RS 660, while the front headlight cluster’s cornering lights will be activated to offer better lighting through corners based on bike lean angle.

The full IMU equipped APRC suite is standard

The full run down includes Aprilia Wheelie Control, Aprilia Cruise Control, Aprilia Quick Shift (bidirectional), Aprilia Engine Brake, Aprilia Engine Map and Aprilia Traction Control, although the last is not listed as being specifically cornering sensitive on the Factory or the RS 660, despite the IMU.

Five ride modes, split between three for the road and two for the track handle presets of these settings, and are further customisable to get things just right for the rider.

The Factory comes in a Factory Dark colour scheme

To stand out in the crowd, the Tuono 660 Factory will arrive in a Factory Dark graphic, with single-seat tail fairing and lighter pegs for both rider and pillion.

All in all it looks like the Tuono 660 Factory will be the version for those who wanted the purity of the full RS 660 spec machine, while retaining the nakedbike feel.

2022 Aprilia Tuono 660 Factory

The current 2021 Aprilia Tuono 660 currently retails for $20,430 ride-away, with the price tag on the RS 660 $20,730 in comparison. It seems likely the new Tuono 660 Factory will demand a premium – perhaps even over the RS 660 with which it shares the higher spec components, however pricing is yet to be confirmed with delivery also a long way off – currently quoted as September 2022…

2022 Aprilia Tuono 660 Factory – Bi-directional quickshifter

2022 Aprilia Tuono 660 Factory Specifications

2022 Aprilia Tuono 660 Factory Specifications
Engine type Aprilia forward-facing parallel twin-cylinder, four stroke, liquid-cooled with radiator and water-oil heat exchanger, DOHC with silent chain on the right side, four valves per cylinder
Bore and stroke 81 x 63.93 mm 
Engine capacity  659 cc 
Compression ratio 13.5:1 
Maximum power at crankshaft 100 hp (73.5 kW) at 10,500 rpm  
Maximum torque at crankshaft 67 Nm (6.83 kgm) at 8500 rpm  
Fuel system Airbox with front air vent. Two ∅48mm throttle bodies, Ride-by-wire management 
Ignition  Electrical  
Lubrication Wet sump  
Transmission Six gears with Aprilia Quick Shift (AQS) up and down system 
Clutch  Multiplate wet clutch with slipper system 
Secondary drive Chain, drive ratio 16/43  
Electronic management Six-axis IMU, APRC suite that includes ATC (traction control), AWC (wheelie control), AEB (engine brake) AEM (engine mapping), ACC (cruise control), five riding modes (Road and Track, 3 pre-set and 2 customisable) 
Chassis Aluminium dual beam chassis with removable seat-supporting subframe 
Front suspension Kayaba 41 mm upside down fork with top out spring, aluminium pins to fasten radial callipers. Both stanchions allow for rebound, compression and spring pre-load adjustment. Wheel travel: 110mm 
Rear suspension Asymmetric aluminium swingarm. Single shock with top out spring and separate reservoir, adjustable in rebound, compression and spring preload. Wheel travel: 130 mm 
Front brake  ABS, 320 mm double disc, Brembo radial callipers with four∅ horizontally opposed 32 mm pistons.  Radial pump and metal braided brake hose 
Rear brake  220 mm diameter disc; Brembo calliper with two 34 mm separate pistons. Master cylinder with separate reservoir and metal braided hose, Multi-map Cornering ABS  
Wheels Aluminium alloy, front: 3.50 x 17”, rear: 5.50 x 17” 
Tyres Radial tubeless, front: 120/70 ZR 17 rear: 180/55 ZR 17 (alternatively 180/60 ZR17) 
Dimensions 
Wheelbase 1370 mm  
Length 1995 mm  
Width 805 mm 
Saddle height 820 mm
Headstock angle 24.1°
Trail 104.7 mm 
Kerb weight 181 kg
Dry weight 169 kg 
Emissions compliance Euro 5  
Fuel consumption 4.9 litres/100 km  
Fuel tank capacity 15 litres
Colour range  Factory Dark 
Price/Arrival TBA/September 2022
2022 Aprilia Tuono 660 Factory – Brembo brakes
2022 Aprilia Tuono 660 Factory – Dual layer fairings
2022 Aprilia Tuono 660 Factory – Single-seat setup with cowl
2022 Aprilia Tuono 660 Factory – Switchblock
2022 Aprilia Tuono 660 Factory – Throttle and starter
2022 Aprilia Tuono 660 Factory
2022 Aprilia Tuono 660 Factory

Source: MCNews.com.au

Aprilia to power new North America Talent Cup

Aprilia RS250SP2-based Road to MotoGP series launches in US


The Road to MotoGP will expand in 2022, with the introduction of the North America Talent Cup in the USA, which will be a collaborative effort between MotoAmerica and Rise Moto, with Aprilia RS250SP2 machinery used for the single-make series.

The North America Talent Cup will look to follow the success of the Aprilia Sport Production Championship in Europe (pictured)

The new North America Talent Cup will aim to provide riders across the continent with a link on the Road to MotoGP program, creating the stepping-stone between the FIM MiniGP North America Series and the Red Bull MotoGP Rookies Cup or FIM Moto3 Junior World Championship. The sanctioning body will be the American Motorcyclist Association and FIM North America.

Wayne Rainey – MotoAmerica President

“The new North America Talent Cup will most definitely help us with our goal of developing more young riders who aspire to compete and represent the U.S. internationally, and we’re happy to be working with Dorna, Aprilia and Rise Moto to help make this happen. This program ensures that we will continue to build a system where young racers can advance their talents in a program designed to give them the tools they need to succeed. We look forward to the first race at Circuit of The Americas in April and to having the North America Talent Cup join us in our season finale at Barber Motorsports Park in September.”

Aprilia RS250SP and SP2 machinery has been in use for a similar purpose in Europe for a while with great success

Riders will race on equal Aprilia RS250SP2 machinery and be between 13 and 16 years of age for the first season, with the minimum age raising to 14 from 2023 – as it will be globally for similar competitions.

Massimo Rivola – CEO of Aprilia Racing

“The North America Talent Cup, as a forge of future talent, fully reflects Aprilia’s racing philosophy of training technicians and riders who have gone on to make sports motorcycling history. Promising young American talent can count on a product we are proud of, the RS 250 SP2, already extremely popular as an intermediate step between MiniGP bikes and ‘high wheel’ bikes, thanks to its combination of performance and easy operation. I’m certain that we’ll see fun and educational races truly capable of launching new talent.”

Aprilia Racing Technical Director Romano Albesiano (L) with Rise Moto CEO Brandon Cretu

The Aprilia RS250SP is already in use in the Aprilia Sport Production Championship in Europe, as part of the CIV or Italian Speed Championship, offering a Junior event with riders aged over 11 able to get started track racing. The RS250SP used there was developed by Aprilia Racing in collaboration with Ohvale.

Both SP and SP2 versions of the bike are powered by 250 cc four-stroke engines, while running components from Öhlins, Brembo, SC Project and Marchesini to name a few.


North America Talent Cup Equipment & Partners

Riders will race on equal Aprilia RS250SP2 machinery, with an affordable, complete race package to be priced especially for competitors.

The sole, official tire supplier will be Dunlop. Seven sets of tires will be provided per rider, per season.

KYT will be the helmet provider, providing two helmets per rider per season along with trackside support.


2022 North America Talent Cup Calendar

The North America Talent Cup will be run across the USA as an Amateur National Series. The series will be limited to 20 riders for the first year with aims to expand the amount of riders permitted to 26 by 2023.

The season opener is planned to take place alongside MotoGP at the Circuit of the Americas. The remaining rounds will be held in partnership with AMA sanctioned racing organization WERA, and the final round will be with MotoAmerica at their season finale at Barber Motorsports Park.

The Aprilia Sport Production Championship on track in Europe on the Aprilia RS250SP

Road to MotoGP Opportunities

Riders accepted into the North American Talent Cup will benefit from trackside coaching at each round from professional riders, as well as training in communication, fitness and nutrition.

The Champion of FIM MiniGP North America Series will automatically gain a place on the North America Talent Cup grid the following season.

The top two in each season of the North America Talent Cup will be invited to take part in the selection event for the following season of the Red Bull MotoGP Rookies Cup.


North America Talent Cup Applications

Applications for the inaugural Cup will open on the 1st of December and close on the 31st of December 2021. Find out more about the new series, and how to apply, at www.northamericatalentcup.com.

Carmelo Ezpeleta – CEO of Dorna Sports

“We are delighted to announce this new project with Rise Moto and MotoAmerica, creating a vital new path on the Road to MotoGP. With the incredible success of the first FIM MiniGP World Series, we are more committed than ever to creating the best possible pathway for young riders from all over the world to further their careers, and the new North America Talent Cup, along with the MotoAmerica Championship, will complete the Road to MotoGP for riders across that continent. The support of Aprilia sees a new manufacturer become a key player on the Road to MotoGP, and all our partners will ensure the series is competitive and affordable — removing as many barriers as we can for those who wish to begin a career in racing and ensuring young talent has the best possible stage on which it can shine.”

Rob Dingman – AMA and FIM North America President

“The North America Talent Cup is a perfect complement to MotoAmerica’s development efforts and will provide a critical element to the development of young road racers in North America.”

Source: MCNews.com.au

2021 Aprilia Tuono V4 & Factory Review | Motorcycle Test

2021 Aprilia Tuono V4 and Tuono Factory Review

By Rennie Scaysbrook, Photography by Larry Chen


Considering their looks, you could be forgiven for thinking the Aprilia Tuono and Aprilia Tuono Factory are all new motorcycles. However, look closer, and you may be mistaken.

2021 Aprilia Tuono V4
2021 Aprilia Tuono V4

Both machines share a brand new face that finally breaks from the original design we saw over a decade ago, resplendent with LED lighting and fancy inboard winglets down the sides near the radiator. And there’s the same swingarm from the RSV4 that was a new addition for 2021, lauded for its extra rigidity that we loved when testing the superbike at Laguna Seca earlier this year.

2021 Aprilia Tuono V4 Factory
2021 Aprilia Tuono V4 Factory

But the big news is the base model Tuono is no longer just a watered-down version of the Factory. It’s a proper model in its own right, going after a chunk of the market currently occupied by machines like the BMW S 1000 XR and KTM 1290 Super Duke GT.

This is something Aprilia should have done years go. And it’s not just me saying that.

Traditionally, the base model was the bike you bought if you either didn’t have the cash for the Factory, or you wanted a bare-bones machine on which to exploit your modifying dreams. However, for 2021, that’s all changed.

The standard 2021 Aprilia Tuono V4 now boasts some features aimed at wider appearl
The standard 2021 Aprilia Tuono V4 now boasts some features aimed at wider appearl

Using the same motor and twin-spar chassis as the Factory, the base model Tuono gets 20 mm higher-set handlebars, a new subframe with a wider passenger seat and lower footpegs, new luggage options like side and tank bags, and a taller windscreen. These choice improvements have shifted the model’s focus into the sporty sports-touring segment, and it’s not a moment too soon.

The standard version now receives taller bars, as well as traditional Sachs suspension
The standard version now receives taller bars, as well as traditional Sachs suspension

Unfortunately, the base model also gets blander colors than the red/black the Tuono Factory gets. Still, fitted to the touring model (we’re calling it that from now on), is the conventionally-adjusted, fully-adjustable, Sachs suspension, while rubber is the Pirelli Rosso Corsa III tire.

A Sachs shock is also featured on the rear
A Sachs shock is also featured on the rear

Yet, the Tuono platform really isn’t that different when you strip the bodywork and suspension away and reveal what’s inside. Over the years, each Aprilia Tuono model, aside from when it grew from a twin to a four-cylinder nakedbike, has never been a revolutionary upgrade. Rather, they’ve been concerted, thought out improvements, delivered every few years to keep the Tuono models at the head of the nakedbike pack.

It’s been this way because Aprilia nailed the four-cylinder Tuono so god damn well when they first bought it out in 2011 that they’ve never had to reinvent the wheel. Instead, they’ve just given it a spit and polish.

The Factory in comparison runs semi-active Ohlins Smart EC 2.0
The Factory in comparison runs semi-active Ohlins Smart EC 2.0

The Factory is still the king daddy of the Tuono range and thus gets plenty of the fruit not found on the base model. There’s semi-active Ohlins Smart EC 2.0 suspension, a short, tinted windscreen, the razor-sharp RSV4 tail section and passenger footpeg set-up, racier colors more like what we used to see on the WorldSBK grid, a polished frame finish, and track-specific Pirelli Diablo Supercorsa SP rubber.

The two variants share the V4 1000 engine, now Euro5 compliant
The two variants share the V4 1000 engine, now Euro5 compliant

Aside from that, the spec’ sheet between the two bikes remain pretty much the same. That beloved, 1077 cc, 175 hp V4 remains largely unchanged except it now comes with Euro 5 compliance. This has given the Tuono a touch of flat spotted-ness in the mid-range but considering how badly the noise and pollution regulations hurt modern performance engines, Aprilia has navigated this maze well and given the rider plenty of performance for the payment.

Six modes are split into three for the road and three for the track...
Six modes are split into three for the road and three for the track…

The motor’s performance is mitigated by six riding modes (three for the road, three for the track, including one programable road mode and two programable track modes), cruise control, three-stage engine brake, ABS, launch control and power modes, eight stage traction control, six stage wheelie control and turn-by-turn navigation accessed by a new mission control switchblock on the left handlebar.

The dash is part of the revamp we first saw back with the RS 660 and later the new RSV4 – a pretty bland design if we do say so – but it’s easy to navigate and use, which is number one in my book.

The dash has been updated to match what's seen on the new 660 models
The dash has been updated to match what’s seen on the new 660 models

The electronics deserve special mention because they’re powered by the new Marelli ECU 11MP, which has a four-times faster clock frequency and four-times the amount of memory than last year.

Via information fed by the six-axis Inertial Measurement Unit, the ECU can now calculate the happenings of the motorcycle much faster than before. For example, trail braking with the Cornering ABS kicking and while monitoring traction control and engine brake level. It’s not like it couldn’t do this stuff before – it could – it just does it faster and more accurately now.

The Ohlins Smart system also uses a different adjustability scale to what many rides may be used to
The Ohlins Smart system also uses a different adjustability scale to what many rides may be used to

Having ridden many thousands of road kilometres on the Tuono V4 Factory, I can tell you the feeling from the hot-seat is eerily similar to what it was in 2020. The Factory gets that outstanding Ohlins Smart EC 2.0 suspension for the 43 mm NIX fork/TTX 36 shock, and the feeling at the bar is one of total connectedness to what’s happening around you.

If you’ve never used the Ohlins Smart system before, it can be a little confusing, with (in automatic level) no compression/rebound adjustment. It’s all done according to what you want at any given point of the ride. Need more support under braking? Dial in Brake Support.

Adjustability is handled via dialling Brake and Acceleration Support up and down with the Ohlins system
Adjustability is handled via dialling Brake and Acceleration Support up and down with the Ohlins system, and well suited to poor road surfaces

Conversely, if the Tuono is squatting too much under acceleration, dial in Acceleration Support. The result is you can easily tune the ride to exactly how you want, making the Tuono’s ferocious nature a little less intimidating.

Riding up Angeles Crest just east of Los Angeles, the roads are crappy at best, so I left the Tuono in the softest automatic setting and was more than happy to leave it there. Even on its softest setting, the Tuono V4 Factory is god’s gift to road apexes. You simply need to look where you want to go and the Tuono will take you there, slicing its way up your favourite mountain road like child’s play.

If you start jacking the suspension stiffness up via the dash the ride can get a bit on the rough side – the track settings really are only good for when you’re absolutely hammering/on the track, otherwise it’s your bum that’ll take the hammering.

Aprilia have also smoothened initial throttle response even in the most aggressive mode
Aprilia have also smoothened initial throttle response even in the most aggressive mode

Aprilia’s done well to smooth out the initial throttle response with the new electronics when in the most direct mode. Chassis balance is always maintained when cranked over and you dial in increments of throttle – an important factor given there’s a claimed 175 hp on tap.

Despite that massive number, the Tuono can be a real pussycat in the city. You’re not faced with a one dimensional machine here. The Tuono V4 Factory can do pretty much everything you ask, except this time it’s the base model which it cannot trump. I know, I’m shocked to say that, too.

The standard Tuono V4 can now be considered the 'Touring Tuono'
The standard Tuono V4 can now be considered the ‘Touring Tuono’

Switching to the Tuono V4, this is where Aprilia have really hit a six. Taking almost all the good bits of the Factory and none of the bad, the Touring Tuono is a comfier, plusher, more usable machine that most road riders need.

I absolutely abhor the term “real-world”, but the touring model is much more applicable to everyday situations. In this instance, I find it a shame that Aprilia did not grace that base model Tuono with saddle bags as standard, given its undoubted touring prowess.

The only missing standard feature is some panniers
The only missing standard feature is some panniers, with the screen ideal for those under 176 cm

Still, the higher set handlebars and taller windscreen make for a more pleasant and relaxed ride than what you’ll get on the Factory, which is as much a stripped nakedbike as you can get. The base model still gets the 175 hp and same frame, so you’re really not missing out on much, aside from the electronic suspension.

But here’s the good news. The Sachs suspension is a brilliant piece of kit. Just like it is on the base mode RSV4, the Sachs suspension is all most riders will need. Yes, having electronic adjustment is a fancy tool in the box, but conventionally adjusted suspension is still king in my book and the fact Sachs has been on an upward curve in the last few years only adds weight to the argument.

The standard Tuono V4s Sachs setup is stiffer than the Ohlins
The standard Tuono V4s Sachs setup is stiffer than the Ohlins

On the road, the Sachs suspension is a little stiffer than the Ohlins but bump absorption is nothing to complain about, neither is the side of the tyre feel. You can bank the base model in with the same confidence as the Factory, albeit in better comfort. This is especially so if you’re under 176 cm tall, as the windshield cut off point should enable the wind to sail right over your helmet, rather than buffet your forehead to bits like on something like the BMW S 1000 XR.

The 'Touring Tuono' now offers great competition to the likes of the S 1000 XR and Super Duke GT
The ‘Touring Tuono’ now offers great competition to the likes of the S 1000 XR and Super Duke GT

Both models are prime examples of the best of nakedbiking, and being a hot-head I’ll always go for the Factory. But I cannot hide my enthusiasm for the new base model. This is the move Aprilia should have made when the V4 first came out, in which case they would have trumped BMW and KTM by years.

The Factory remains the top dog of course
The Factory remains the top dog of course

Oh well, never mind, it’s here now. And although the Factory is and always will be the king dong as far as Aprilia Tuono nakedbikes are concerned, it’s the base model I’ll be raving about when the pubs eventually reopen. And at $28,030 ride away, the few grand you save over the Factory will buy you plenty of beers!

The latest Tuono V4 offerings get the big thumbs up
The latest Tuono V4 offerings get the big thumbs up

2021 Aprilia Tuono V4 1100 Specifications

Source: MCNews.com.au

It’s official! Vinales to race with Aprilia from next round

Vinales to race Aragon with Aprilia

All the pieces have now fallen in place for the Aprilia Racing rider line-up after Maverick Viñales’ début astride the RS-GP during the two days of testing on the Misano Adriatico circuit.

The Spanish rider, extremely impressed by the first contact with the Italian team, will be on the track officially from the Aragón GP, scheduled to be held on the weekend of 12 September. He will take a spot on the Aprilia Racing Team Gresini alongside Aleix Espargaró, who just brought the Noale-based manufacturer their first podium in MotoGP at Silverstone.

Maverick Viñales’
Massimo Rivola – Aprilia Racing CEO

We are extremely proud to be able to announce our plans for the current season and for 2022 with the goal of optimising the contributions of our three riders to the utmost. Alongside our confirmed rider, Aleix, it is our pleasure to welcome a talented athlete like Maverick to the Aprilia Racing team, who demonstrated a great feeling with the team and the bike straight away and who I am confident will be able to give his best as early as the Aragón GP. At the same time, we are also confirming Lorenzo’s role as 2022 test rider. This is a fundamental position that rewards the great efforts he has demonstrated in developing the new RS-GP, whereas he will finish out the 2021 season taking advantage of the wild cards that we’ll decide on together as soon as he is back to 100% fitness.

Maverick Viñales’

Lorenzo Savadori will therefore be confirmed as test rider for the 2022 season, completing an extremely high level trio with the goal of continuing to improve the young RS-GP project. For the rest of the 2021 season, his presence on the track will not be lacking, taking advantage of the wild cards Aprilia has available. Lorenzo’s work schedule will be formalised as soon as he has recovered fully from the injury suffered during the Styria GP, a fractured right malleolus that required surgery.

Romano Albesiano – Aprilia Racing Technical Director

The decision to have Maverick on the track from Aragón is a direct result of the tests done in Misano. It was not a given that, after a career spent up to now on a bike with an in-line engine, Maverick would have a good feeling with our V4 straight away. This is why the test on this track, historically not an easy one for our bike, was an important moment of assessment. Therefore, we are satisfied with Maverick’s immediately positive reactions, which demonstrated a good feeling both with the RS-GP and with the team and our work method. His and Aleix’s talent, combined with the experience Lorenzo has gained this season, make us optimistic about the future of our MotoGP project.

Maverick Viñales’

Source: MCNews.com.au

Maverick Vinales to ride Aprilia RS-GP next week at Misano

Maverick Vinales heading for two-day Misano Test with Aprilia

Maverick Vinales’ debut on the Aprilia RS-GP will take place on the Italian track at Misano Adriatico.

The first contact between the Spanish rider and the Italian team is scheduled for two days of testing on 31 August – 1 September.

This marks the start of Maverick’s integration into the new structure that will accompany him throughout the 2022 season, a gradual approach to the improved harmony that is essential in such an extraordinary championship as modern MotoGP.

Romano Albesiano – Aprilia Racing Manager

“From a technical point of view, it is always fascinating to listen to the impressions of a rider who is testing your bike for the first time. Especially with a champion like Maverick, who we are pleased to welcome into the Aprilia Racing family. After the great work carried out on the track by the racing department over the last two years, we are adding yet another piece to the path of growth that we are undertaking with encouraging results. Clearly the first approach involves a very practical adaptation phase, in terms of ergonomics and setup, which we know vary for each rider. But I’m sure that Maverick’s talent and speed will come to the fore right away and I can’t wait to start working together”.

Source: MCNews.com.au

Dovizioso spent two days on Aprilia RSGP at Misano this week

Aprilia talking contracts for 2022

Andrea was finally able to test the RS-GP in ideal conditions over two days at Misano this week after the last test in Mugello was plagued by rain.

Andrea Dovizioso

Andrea put in 78 laps on Wednesday and 48 on Thursday and Aprilia have stated that Dovizioso ‘lapped at decidedly fast times’, making a clear improvement from one day to the next.

Andrea Dovizioso

It was a very interesting test. Testing on a third and different circuit was extremely important to understand the bike better and to see which points need to be developed. We tested and changed a lot of things in order to better understand many details which, in fact, we gathered more accurately, identifying how to improve and where, on the other hand, we lose something with certain changes. With the next scheduled tests, we’ll be able to make more comparisons and discuss our ideas better.

Andrea Dovizioso

Aerodynamics, electronics and the general dynamic of the bike, with various chassis solutions tested over the two days: these were the areas explored, also in view of developments on the RS-GP both for the second half of this season and to define the bike for next season.

Massimo Rivola – Aprilia Racing CEO

These were two very positive days. We are pleased with these tests that gave us some important pointers and demonstrated the bike’s progress which has already been seen in the races. It’s a job that we will continue as scheduled in July. Andrea has proven to be a great rider in terms of sensitivity and understanding the way the bike behaves. Parallel to testing, Aprilia Racing is taking measures to find the best solution in terms of the riders to put on the grid in 2022, without having to wait for the outcome of the next tests in July. Andrea is certainly included in the solutions we are assessing, but there are very interesting and valid alternatives on the table and a decision must be taken soon so we can properly plan the future strategy of the team. The Assen weekend will be extremely important in this regard.”

Dovi back in MotoGP for 2022?

Source: MCNews.com.au

Aprilia RS 660 Factory Works Trofeo ‘Trophy’

Aprilia RS 660 Factory Racer


Aprilia will be offering a special Trofeo or ‘Trophy’ edition of the RS 660, following the success of the single-make series in Italy, making available a track/race version developed by the Aprilia Racing Department, and joining the Factory Works programme.

Aprilia RS 660 Trofeo

Alas, this RS 660 is not available from your local Aprilia dealer, as Aprilia sell them direct, in the same way that the RSV4 race programme is managed. Thus if you want to get your paws on one, then you will need to deal directly with the Aprilia Race Department in Noale.

Stripped back for racing, the RS 660 Trofeo removes the ignition switch assembly and ABS system, saving weight and helping simplify the machine. The braking system is also modified running independent lines, while the ABS control unit is retained and connected to the electronic system which is integrated.

The ECU is a reprogrammed Race version which offers maximum performance exclusively for track use, and is calibrated for the SC Project racing exhaust included with the bike.

The TFT display has also been reprogrammed and features an integrated buttoon block on the left hand switchblock.

An SC Project exhaust is run alongside an Ohlins rear shock

Suspension has been beefed up with “Misano by Andreani” internal cartridges, and offers compression, rebound and preload adjustability.

At the rear on the other hand, an Öhlins AP948 shock absorber is fitted, offering the same level of adjustability as the forks.

Forks run “Misano by Andreani” internal cartridges and race switches are fitted

Tyres are a set of Pirelli Supercorsa V3 SC1 rubber.

The RS 660 Trofeo’s ride height is also lower due to the racing upper steering yoke fitted and adjustable semi-handlebars, with footpegs likewise adjustable.

Fibreglass fairings are by Cruciata Racing and are also part of the package, while retaining the RS 660’s styling and the Zanasi Group have painted them.

Cruciata Racing fibreglass fairings

Aprilia are also boasting that they’ve tuned the bike to produce 105 horsepower, with the dry weight brought down to 153 kg. In comparison the dry weight on the RS 660 is quoted as 169 kg with 100 hp.

The engine is tuned for 105 hp with the SC Project exhaust and runs case protectors

Part of that weight reduction is the removal of the secondary air system and thermostat, with aluminium guards also installed on the clutch and alternator covers, and a Spring air filter fitted.

Aprilia’s Factory Works RS 660 Trofeo

Pricing in Europe, excluding VAT is quoted at €14,700.00, which thrown into the currency exchange calculator equals about $23k in Australian dollars, although obviously that’s excluding VAT (GST here) and any other associated costs that might be added should the Aprilia RS 660 Trofeo come to Australia. 

Source: MCNews.com.au

2021 Aprilia RSV4 Tested | Motorcycle Review

Aprilia RSV4 and RSV4 Factory Review

When Aprilia bought the superlative RSV4 to market in 2009, the collective superbike fraternity was left rather embarrassed.  The RSV4 was the first superbike to combine 250cc GP chassis philosophy with superbike speed, and when you put it against the CBR1000RR or Yamaha YZF-R1 of its day, it looked like a 600 in comparison.

It was a dozen years ago when the Aprilia RSV4 was first released
2009 model pictured

The superbike game has changed drastically since that time. Bikes have become blindingly quick and more tech-laden than ever, but like a young man who has spent the past decade or so in the gym and eating well, the RSV4 has matured into an athletic, muscle-bound beast but it hasn’t forgot the good manners and cheeky charm that won journalist’s hearts and rider’s wallets right when the GFC was in full swing.

2021 Aprilia RSV4 Factory

The new RSV4 has a similar feel to the original but, make no mistake, this is no simple Bold New Graphics makeover. You can ride away on the $31,290 base model RSV4 with cast aluminium wheels and conventionally-adjusted Sachs suspension, while the premium RSV4 Factory with lighter forged aluminium wheels and electronically-adjusted semi-active Ohlins Smart EC2 suspension will set you back $38,490 by the time you ride it out of an Australian Aprilia dealership this June.  The RSV4 band of brothers is here to knock off arch rival Ducati in the Oversized Superbike Showdown.

2021 Aprilia RSV4 Factory and RSV4 sibling

The only difference between the two models is the aforementioned wheels and suspension, and also paint choices (we’ll get to the benefits of the Ohlins vs Sachs in a tick). Everything else is the same across each bike, which includes a now 1099cc V4 motor with a lighter crankshaft packing a pants-tightening 217 hp at 13,000 rpm and 125 Nm or torque at 10,500 rpm. 

1099 cc – 81 mm bore x 53.32 mm stroke – 217 hp at 13,000 rpm

The great thing for Aprilia is they’ve managed to get the donk through the Euro5 emissions regulations without losing too much in the way of midrange torque. As the old saying goes, “if you want more inches, stroke it”, and that’s exactly what Aprilia has done by going from 52.25 mm to 53.32 mm to accompany the MotoGP-specific 81mm bore.   

Rennie on the 2021 Aprilia RSV4 at Laguna Seca

Compared to the 2020 RSV4, the ’21 edition maintains more torque from 4500 rpm right up 13,500 rpm, with a substantial increase from 5000 to 8000 rpm, right where you’ll spend most of your time on the street and right where manufacturers like Honda and BMW got so hurt with their Euro5 emissions performance block. 

Rennie on the 2021 Aprilia RSV4 at Laguna Seca

Without sounding like a regurgitated press release, I can tell you from the hot-seat that the new motor spins up with serious pace. From the almost dead stop of Turn 11 at Laguna Seca, the forward momentum delivered by the new motor is substantial. The ’21 rips through the rev range much quicker than before, although I will hold off on my opinion on absolute top end performance as Laguna’s front straight is about a quarter of what Mugello’s is like, where I rode the 2019 RSV4.

Rennie on the 2021 Aprilia RSV4 at Laguna Seca

Helping this mammoth amount of power is the mix of new twin 48 mm throttle bodies, fuel injectors, new ECU and revised throttle maps via the Aprilia Performance Ride Control (APRC) suite. I’m not going to sit here and pretend like I know exactly what’s going on beneath me with regards to all those sparky things, but suffice to say the new bike, yes it’s faster, but the throttle is much smoother in how it applies the torque to the tyre, which makes just getting on with the job of riding that much easier. 

Rennie on the 2021 Aprilia RSV4 at Laguna Seca

The electronics at last feature engine brake control, bringing the RSV4 into line with the bike that was modelled on it in the RS 660, and gives the RSV4 equal footing with the current generation of superbikes. The APRC system, complete with its Bosch IMU, features three preset riding and three programmable modes in which you can alter everything from engine braking to traction, launch, and wheelie control, Cornering ABS, slide control, cruise control, and Aprilia has developed an all-new quick-shifter for utterly seamless full power gear shifts. 

APRC system (Aprilia Performance Ride Control) that includes engine maps (AEM), engine brake control (AEB), traction control (ATC), wheelie control (AWC), launch control (ALC), cruise control (ACC), speed limiter (APT). 6 riding modes (3 Road, 3 Track)

Aprilia’s crammed a shitload of information into the five-inch TFT dash, but like the APRC systems that have gone before the ’21 edition, Aprilia’s engineers have done an excellent job on the user experience and design interface so you can get to the settings you want quickly, make the changes you want and just get on with riding.

Rennie on the 2021 Aprilia RSV4 Factory at Laguna Seca

The motor and the electronics are impressive, but what stands out more is what made the original RSV4 so good—its ability to decimate corners. Aprilia has fitted their first production inverted swingarm for the ’21 RSV4, which they claim is a massive 30 percent stiffer and saving 600 grams of unsprung weight. The result is the RSV4 gives such beautiful feel on the side of tyre, especially when you start dialling the power back in past the apex. 

6-speed cassette type gearbox Gear lever with Aprilia Quick Shift electronic system (AQS)

The 2019 edition was no slouch here, but it used technology and thinking from a number of years ago. The inverted swingarm theory was taken from Aleix Espargaro’s RS-GP machine and was clearly a masterstroke, helping the RSV4 rail with the fluidity of a 600 but the power of a (bigger) superbike.

Airbox with front dynamic air intakes. 4 Marelli 48-mm throttle bodies with 8 injectors and Ride-By-Wire engine management.

Aprilia’s really gone to town on the aerodynamics for the RSV4. New LED lights, similar to the RS 660, adorn the front of the bodywork, while revised downforce winglets either side of the fairing help keep the front wheel down under acceleration and increase braking stability when it’s time to heave on the Brembos. 

2021 Aprilia RSV4

A wider windshield and an increased area for your chin to sit on when in a full tuck has been developed, and makes this iteration far more comfortable and less tiring to ride. To that end, the engineers have lowered the seat height by nine millimetres and the foot-peg position is 10mm lower, while amazingly giving you an extra 1.5-degrees of lean angle when cornering, not taking 1.5-degrees away.

Rennie on the 2021 Aprilia RSV4 Factory at Laguna Seca

You don’t feel as cramped on the 2021 RSV4, which is something taller riders will love. The original development rider for the RSV4 was pint-sized Max Biaggi—in fact you could say the RSV4 was made for Max so he could go and win Aprilia a couple of WorldSBK crowns. It now appears Aprilia is listening to riders of taller stature, as at 183 cm tall I found the new machine to be an almost ideal fit.

Rennie on the 2021 Aprilia RSV4 Factory at Laguna Seca

Now. The big elephant in the room. Is the Factory still worth the dosh over the base model? Yes. But there’s a but. 

Standard bike has Sachs fork ∅ 43 stanchions, adjustable compression and rebound, travel 127 mm

I remember when I was at AMCN years ago and we rode the base and Factory back-to-back and within two corners you could tell everyone would go for the Factory. But that was before the advent of electronic suspension, and in that time the Sachs suspension has improved out of sight.

RSV4 Factory has Smart EC 2.0 electronically managed Öhlins NIX fork. ∅ 43 mm stanchions, with TIN surface treatment Aluminium radial calliper mounts, adjustable in hydraulic compression and rebound damping and spring pre-load, 125 mm travel

While sending it around Laguna, I was perfectly happy with the base model’s conventional suspension. I knew exactly what was happening as I didn’t have the computer constantly changing the suspension beneath me, like what happens when you’re in dynamic mode on the Factory. 

RSV4 Factory

The base model was quite the revelation, but once we put the Factory in manual mode on the dash where you could individually pick your rebound/compression, the ride became much more predictable. That allowed the lighter wheels on the Factory to really shine in the change of direction, giving the Factory a clear advantage over the base model. 

RSV4 Factory gets forged aluminium alloy wheels, completely machined, with 5 split spoke design

However, the difference is not as big as you may think, and if you don’t need electronic suspension (which I suspect many do not), you’d be just fine to save your cash and go for the base model (and buy some lighter wheels with the money you’ll save because god knows you don’t need to make the engine faster).

2021 Aprilia RSV4 Factory and RSV4 sibling

I must admit I’m a little disappointed in the colour option for the base in the rather drab grey and silver, whereas the Factory gets two choices of Aprilia’s traditional racing colours of purple, black and red or the current MotoGP-style black and red. For that reason alone, I think more riders will gravitate towards the Factory, but don’t let that saw you alone because the base RSV4 is a truly excellent machine.

2021 Aprilia RSV4 Factory

Aprilia’s really nailed this one. They’ve modernised an already classic superbike design and made a compelling case for top Italian superbike (or top superbike overall, for that matter). It sounds incredible, goes like a bat out of hell and rails corners like no one’s business, be it in base or Factory modes. Every couple of years the superbike moves a step forward, and the RSV4 is certainly at the head of this year’s class. 

2021 Aprilia RSV4 Factory
Aprilia RSV4 Factory: Technical Specifications [RSV4 data in brackets]
Engine type Aprilia 4 longitudinal 65° V4 cylinder, 4-strokes, liquid cooling system, double overhead camshaft (DOHC), cooling system, double overhead camshaft (DOHC),
Bore and stroke 81 x 53.32 mm
Capacity 1,099 cc
Compression ratio 13.6:1
Power 217 HP (159.5 kW) at 13,000 rpm
Torque 125 Nm at 10,500 rpm
Power supply Airbox with front dynamic air intakes. 4 Marelli 48-mm throttle bodies with 8 injectors and Ride-By-Wire engine management.
Transmission 6-speed cassette type gearbox Gear lever with Aprilia Quick Shift electronic system (AQS)
Clutch Multi plate wet clutch with mechanical slipper system
Primary drive Straight cut gears and integrated flexible coupling, drive ratio: 73/44 (1,659)
Secondary drive Chain: Drive ratio: 41/16 (2,562)
Controls management APRC system (Aprilia Performance Ride Control) that includes engine maps (AEM), engine brake control (AEB), traction control (ATC), wheelie control (AWC), launch control (ALC), cruise control (ACC), speed limiter (APT). 6 riding modes (3 Road, 3 Track)
Chassis Aluminium dual beam chassis with pressed and cast sheet elements Available adjustments: headstock position and angle, engine height, swingarm pin height Smart EC 2.0 electronically managed Öhlins steering damper [Sachs steering damper]
Front suspension Smart EC 2.0 electronically managed Öhlins NIX fork. ∅ 43 mm stanchions, with TIN surface treatment Aluminium radial calliper mounts, adjustable in hydraulic compression and rebound damping and spring pre-load, 125 mm travel [Sachs fork ∅ 43 stanchions, adjustable compression and rebound, travel 127 mm]
Rear suspension Upside-down double braced aluminium swingarm; Öhlins TTX monoshock with Smart EC 2.0 electronically managed piggy-back, fully adjustable in: spring pre-load, wheelbase and hydraulic compression and rebound damping. 115 mm travel [Sachs]
Wheels Forged aluminium alloy wheels, completely machined, with 5 split spoke design. [Aprilia in aluminium alloy wheels with 3 split spoke design]. Front: 3.5”x17” Rear: 6”x17”
Tyres Front: 120/70 ZR 17 Radial tubeless.
Rear: 200/55 ZR 17 (alternative: 190/50 ZR 17; 190/55 ZR 17) Radial tubeless.
Dimensions Wheelbase: 1435.8 mm
Length: 2055 mm
Width: 735 mm
Saddle height: 845 mm
Headstock angle: 24.6°
Trail: 104.5 mm
Kerb weight 202 kg (90% fuel)
Emissions compliance Euro 5
Consumption 6.90 litres/100 km
CO2 emissions 160 g/km
2021 Aprilia RSV4
2021 Aprilia RSV4
2021 Aprilia RSV4 and RSV4 Factory
2021 Aprilia RSV4 Factory
2021 Aprilia RSV4 Factory
2021 Aprilia RSV4 Factory
2021 Aprilia RSV4 Factory
2021 Aprilia RSV4 Factory and RSV4

Photography by Larry Chen

Source: MCNews.com.au