Showa suspension lowers seat height

How clever is this Showa suspension that automatically lowers the seat height when the bike is stationary, allowing short people to mount and dismount easier!

No more tip-toeing at the lights or teetering over when trying to get the sidetone down.

The Electronically Equipped Ride Adjustment (EERA) Heightflex suspension system has electronically controlled activators in the hydraulic valve to control oil supply.

Showa has displayed the new suspension system on a Honda CRF1000 Africa Twin.

2018 Honda Africa Twin Adventure Sports shows
Honda Africa Twin

Tall adventure bikes are a natural choice for such a system. They are lowered for mounting and dismounting, but still retain good ground clearance for off-road duties.

However, Showa says it can also be fitted to other models.

Showa doesn’t detail how much it lowers the bike, but they say it will drop in about a second and will resume normal height a few hundred metres after you start again.

Not only does it lower when the bike is stationary, but it also levels out to adjust for the rear weight of a pillion or luggage, much like other systems used on some BMWs and Ducatis.

Sounds like a god-send for short riders.

Although, there are other, cheaper ways short riders can adapt to tall bikes.

Click here to read our tall tips for short riders.

Showa EERA steering

Showa has also announced an EERA electronically-controlled steering damper.

It adapts the damping force in real time to control tank-slappers, speed wobbles and other adverse steering inputs.

The system seems similar to the Swedish Ohlins electronic steering damper.

The Japanese suspension company says both systems were developed during World Superbikes, the Dakar Rally, the Motocross World Championship and the FIM Endurance World Championship.

Source: MotorbikeWriter.com

Capriolo 75 | Capriolo 75 Sport

With Phil Aynsley

PA Capriolo
Capriolo 75

Capriolo was the motorcycle division of the famous Italian aircraft manufacturer Caproni (and named after the local alpine deer).

PA Capriolo
The Capriolo 75 was produced when the Italian firm was banned from aircraft production following WW2

When Italy was barred from producing aircraft after WW II, Count Caproni turned to motorcycles (as did Aermacchi). In fact among their first projects was producing the frame for the first Ducati motorcycle, the 60.

PA Capriolo
The brand actually produced a frame for the Ducati 60

The 75 was introduced in 1951 and production continued until 1958.

PA Capriolo
The Capriolo 75 Normale had a distinctive frame

This 75 Normale is the second version (circa. 1957) of the 75, which featured revised engine parts (mainly the clutch) and hydraulic rear shocks in place of the earlier friction damper types. The front forks were also updated.

PA Capriolo
This later version (a 1957) featured updated suspension and clutch

The motor was unusual in having a longitudinally mounted crankshaft with the flywheel at the front. To complete the weirdness a face-cam system was used instead of a normal lobe cam.

PA Capriolo
Capriolo 75 engine cut-out

Output was 3.5hp at 6000rpm and a pressed steel frame which encompassed the tank was yet another unusual feature.

PA Capriolo
Capriolo 75 engine cut-out

With Count Caproni’s death in 1957 the company was reorganised and renamed Aeromere (Areo Meccanica Regionale).

PA Capriolo
The brand was later renamed Areo Meccanica Regionale

A new line of bikes was then designed including a new 75. Capriolo was taken over by Laverda in 1964.

PA Capriolo
Capriolo 75

Being an Italian company, of course a 75 Sport was soon introduced (1952). It made 4.5hp at 7,500rpm.

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo was taken over by Laverda in 1964

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75 ‘Sport’

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

PA Capriolo
Capriolo 75

Source: MCNews.com.au

Police launch pilot training course

A police senior sergeant and returned rider, has started a training course for returned riders in his district which he hopes will become a pilot for further courses throughout Queensland.

Snr Sgt Peter Waugh of Jimboomba secured a grant from the Queensland Government’s Community Road Safety Grants scheme for the course. It’s called ‘Mouldy Hogs – Motorcyclists of Jimboomba’ safe ride days.

The first Mouldy Hogs course was held on November 24 at the Mundoolun Community Centre with 12 participants. The second course will be held on December 9.

Click here to register or call 1300 961 335. At the moment, it is free for Jimboomba Police District residents, but other riders may attend for $145.

The pilot courses are run by SMART Rider trainer Steve McDowall with police along for the ride.

Jimboomba police training course pilot program
Steve McDowall

Worst rider

“I’m the worst rider in the world,” admits Peter who used to ride a cruiser, but now has a Yamaha Super Tenere.

“I looked at my own situation: I had a bike young, got married didn’t have one for a long time and then came back to it. Sound familiar?

“Bikes have changed in that time and my skills have dulled.”

Peter points to the statistics that show returned riders are over-represented in crash statistics.

“I suppose stats can tell you anything you want. But we are one of the highest fatality injury rates for motorbike riders. So we decided we need to have a look at it and do something,” he says.

“Living and riding in this area we can blame the roads, the conditions, traffic or whatever. We can do that, but the facts are the roads aren’t going to change greatly. If we are on bikes these are the roads we are going to ride.Jimboomba police training course pilot program

“This is what we’ve got to ride on so let’s make it as safe as we can.”

He says the course is not just for returned riders.

“But mainly more mature-aged riders because that’s what the stats are telling us,” he says.

Pilot courses

Peter says the course consists of “some class work, then a small stage in carpark and the rest of day with instructors out on the roads we ride”.Jimboomba police training course pilot program

“We started it down here because these are the roads they will be riding on. It’s their playground.

“But this is not a track day in any shape or form.”

Peter says there is a police presence, but not as official instructors.

“They are along for the ride and will provide feedback and guidance to riders,” he says.

Jimboomba police training course pilot program

“We are not looking at spoiling their fun or defect their bike, but give them some skills that may help to save their life.”

Jimboomba Police have received funding for 50 riders, but Peter hopes to gain more funding next year and spread the course statewide.

Source: MotorbikeWriter.com

The 6 Most Important Annual Motorcycle Maintenance Updates

Contributed post for our North American readers

A motorcycle is an intricate machine composed of many parts. These should all be checked on a regular basis. Just like if you owned a car and the windshield was cracked, you would take it to
an auto glass shop such as www.richmondhillautoglass.ca, a motorcycle also needs routine maintenance. It helps to detect and fix any small issues that can balloon into major problems.

Here, the goal is to narrow it down to the most important items in need of annual maintenance.

Let’s jump into the most important annual motorcycle maintenance updates.

Tired Tires

An under-inflated tire can easily lead to a blow-out, which can become a major issue on a highway ride. Definitely check on tire inflation regularly to ensure they are balanced just right.

This can be done with a tire gauge and visual inspections. Over time, you’ll learn how to instinctively know if the tire is at a good pressure point.

Tires should also be replaced when the tread wears down. If the tread depth is around 1-2 millimeters, it is replacement time. A motorcycle isn’t worth much without a good set of tires,
so don’t skimp out when replacing them.

Break for the Brakes

Over time, brake fluid becomes less effective and therefore more dangerous on a ride. Brake fluid should typically be replaced every one or two years to ensure the best performance.

Motorcycles typically have two reservoirs for brake fluid. One is near the front on the handlebars and another in the back. Both need to be checked annually.

Additionally, brake pads need to be checked for replacement. If they are thin, they might be due for replacement. If brake pads wear down to the metal, the brake disc will lead to an expensive replacement. This is easily avoided by checking brake pad thickness regularly.

Check the Chain (and Sprockets, Shaft Drives, and Belts)

The combination of chains, sprockets, shaft drives, and belts are essential to the function of the motorcycle. Poor maintenance of these parts will lead to expensive repairs and replacements down the road.
Chains: Chains on the motorcycle need to be constantly lubricated. Experts suggest spraying it with a chain spray whenever you refuel or at the end of the ride. If you do it after each ride, the chain will still be warm, and the oil will be able to soak in and get all of the chain covered. Spray liberally where the chain touches the sprockets. Be careful not to dirty the rear wheel and rim while spraying. A way to avoid that is to put newspaper between the chain and tire before spraying. Allow the oil to soak in for five minutes or so before removing excess oil.
Shaft Drives: This piece requires a little less maintenance, but still deserves attention. Replace the shaft drive oil whenever it is time for an oil change. This will prolong the life of the shaft drive and the bike overall.

Belt Drives: Again, another piece requiring little maintenance. Check and adjust the belt tension anytime the oil is being changed. The belt should always be cleaned for the health of the bike.

Fill the Fuel

This doesn’t just mean to gas up the bike for the obvious purpose of getting the bike to go. Fuel maintenance requires replacing the fuel filter every two years and checking for clogs annually. Fuel filters can be easily damaged by weather, and if it is, should be replaced immediately. If the bike, and therefore the gas, sits for a long time, it should be replaced. Running on gas older than 6 months can lead to damage to the bike. If the bike is sitting for an extended period of time, turn the fuel tap off. This will help prevent fuel from leaking and flooding the carbs or engine.

Always Check the Oil

Oil and oil filter changes will keep your bike healthy and running for a long time. Changing the oil is a great time to check a lot of the other maintenance issues listed here. The oil level shouldbe kept at a high or max level as much as possible. A low oil level can be damaging for the bike.

Battery for life

Just like a car, the battery can lead to breakdowns and a stranded rider. The location of the battery on a motorcycle means it is often overlooked, but it is no less important for maintenance. Batteries need monthly maintenance. It should always be kept at 100% and recharged as needed.

Some tips for maintaining the battery include:

  • Checking the electrolyte level
  • Topping up in a well-ventilated area with deionized or distilled water while wearing gloves and protective glasses
  • Keeping the battery top free of grime
  • Checking all cables, case, and clamps for damage or any loose connections
  • Cleaning terminals and connectors
  • Looking inside for a build-up of sediment, sulfation, or mossing
  • Keeping the exhaust tube free from clogs and kinks
  • Replacing caps
  • Testing the battery with a hydrometer or voltmeter
  • Checking all of this monthly to extend the life of the bike

The goal of a motorcycle owner is to keep the ride running smoothly and safely for as long as possible. Following these maintenance tips will help extend the longevity of the bike and make sure you are safe while doing it.

Source: MotorbikeWriter.com

Kawasaki Updates Ninja H2 Models for 2019

2019 Kawasaki Ninja H2 SX SE+
2019 Kawasaki Ninja H2 SX SE+

Kawasaki blew minds and went on to set records when it released the supercharged 200-horsepower Ninja H2 and 300-horsepower, racetrack-and-experts-only Ninja H2R in 2015. From its 998cc in-line four-cylinder engine force-fed by a 130,000rpm supercharger to its trellis frame, downforce-generating bodywork, Mirror Coated Black paint and Kawasaki River Mark insignia, the Ninja H2 was and continues to be a very special motorcycle.

Read our 2015 Kawasaki Ninja H2 first look review

Since the original models were introduced a few years ago, the Ninja H2 lineup has expanded and it has been updated for 2019. Highlights include the following:

2019 Kawasaki Ninja H2 and Ninja H2 Carbon

2019 Kawasaki Ninja H2 Carbon
2019 Kawasaki Ninja H2 Carbon
  • More powerful supercharged, 998cc in-line four thanks to a new air filter, revised intake chamber and new sparkplugs
  • New Brembo Stylema Monobloc front brake calipers
  • New Bridgestone Battlax RS11 sport tires
  • New TFT full-color instrument display with four selectable modes
  • New smartphone connectivity with Kawasaki’s Rideology the App
  • New all-LED lighting
  • New Highly Durable Paint with “self repairing” top coat on high-touch areas
  • Ninja H2 is available in Mirror Coated Spark Black and MSRP is $29,000
  • Ninja H2 Carbon, which features a carbon fiber upper cowl, is available in Mirror Coated Matte Spark Black/Candy Flat Blazed Green and MSRP is $32,500

2019 Kawasaki Ninja H2 SX SE+

2019 Kawasaki Ninja H2 SX SE+
2019 Kawasaki Ninja H2 SX SE+ with accessory KQR 28L Hard Saddlebags
    • New Kawasaki Electronic Control Suspension, with a Showa 43mm upside-down cartridge fork and a Showa Balance Free Rear Cushion (BFRC) lite shock
    • New integrated riding modes (Sport, Road, Rain, Manual)
    • New Brembo Stylema Monobloc front brake calipers
    • New smartphone connectivity with Kawasaki’s Rideology the App
    • New Highly Durable Paint with “self repairing” top coat on high-touch areas
    • Ninja H2 SX SE+ is available in Metallic Graphite Gray/ Metallic Diablo Black/Emerald Blazed Green and MSRP is $25,000

Read our 2018 Kawasaki Ninja H2 SX SE road test review

2019 Kawasaki Ninja H2R

2019 Kawasaki Ninja H2R
2019 Kawasaki Ninja H2R
      • New Brembo Stylema Monobloc front calipers
      • Redesigned supercharged emblem
      • New Highly Durable Paint with “self repairing” top coat on high-touch areas
      • Ninja H2R is available in Mirror Coated Matte Spark Black and MSRP is $55,000

Check out Rider’s Guide to New/Updated Street Motorcycles for 2019

Source: RiderMagazine.com

Fusion M1 hybrid has rotary engine

No, it’s not the 1970s again — Furion Motorcycles of France plans to resurrect the Wankel rotary engine for their hybrid M1 motorcycle that also has an electric motor.

Rotary engines were big news in the 1970s, most notably in the Mazda RX-8.

There were also many motorcycles with rotary engines. Norton had several models. Others included the Hercules/DKW W-2000, Yamaha RZ201, Kawasaki X99 RCE, Van Veen OCR1000 and Suzuki RE5.

Hercules Wankel rotary engine
Hercules Wankel

Wankel rotary engines seemed a stroke of genius at the time with the cylinders rotating around the stationary camshaft. They were light and compact with high power and smooth revving.

But they had poor fuel economy and high emissions. Furion has now been resolved that by using a back-up electric motor.

Furion M1 Hybrid

Furion Motorcycles’ hybrid M1 sportsbike is so far only CAD images on a computer screen.

However, they say they will power it with a 654cc Wankel rotary engine, an electric motor and five lithium-ion batteries.

The rotary produces 93kW of power (125hp) at 9000rpm and 105Nm of torque at 6000rpm, while the bike weighs 209kg.

An electric motor adds 41kW (55hp) and 100Nm for a total of 134kW (180hp) and 205Nm.

Despite all that power, they claim range of 400km on just 16 litres of fuel.

Furion M1 sits in a tubular trellis frame on 43mm upside-down forks and rear monoshock with 310mm dual disc brakes and six-speed transmission.

Furion M1 Hybrid SportBike with Wankel rotary engine
Instruments

Hybrid future

Furion is not the only company looking at hybrid technology for the future.

Honda is making hybrid scooters, Yamaha is helping to develop hybrid engines for cars, Indian motorcycle company TVS is planning a hybrid motorcycle and the American Defence Advanced Research Projects Agency (DARPA) has developed a stealth off-road motorcycle powered by a petrol engine and an electric motor.

Honda PCX Hybrid scooter battery swap rotary
Honda hybrid and electric PCX scooters

Furion M1 tech specsFurion M1 Hybrid SportBike with Wankel rotary engine

  • Dual-rotor + electric engine 40kw
  • Capacity : 2 × 327 (654cc)
  • Power: 93kW/125hp @ 9000rpm + 41kW/55hp (electric)
  • Total Power: 134kW (180hp)
  • Torque: 105Nm @ 6000rpm + 100Nm (electric)
  • Total Torque: 205Nm
  • Compression: 10.1: 1
  • Mileage: 4L/100km
  • Length: 2095mm
  • Seat: 810mm
  • Clearance: 140mm
  • Wheelbase: 1435mm
  • Wet weight: 209kg
  • Fuel capacity: 16litres
  • Tyres: 120/70/17; 190/50/17
  • Frame: Tubular trellis frame, motor carrier
  • Suspension: USD 43mm forks (adjustable rebound, compression and pre-load); Monoshock horizontal gas type back-link (adjustable pre-load, and rebound)
  • Brakes: Dual 310mm petal discs, 4-piston radial calipers; 250mm petal disk, single-piston caliper transmission
  • Final drive: Chain
  • Clutch: Multi-disc in oil bath
  • Transmission: 6-speed

Source: MotorbikeWriter.com

Wild nostalgia version of BMW R nineT

Would you believe this wild nostalgia custom motorcycle started life as the BMW R nineT and that you can buy actually buy one?

The R nineT is the Bavarian company’s most customisable production bike, but this Nmoto Nostalgia machine has to be the wildest custom version yet.

The Florida custom motorcycle company plans to sell the handmade custom bike for $US49,500 (about $A67,700) on a limited-run basis.

That compares with the standard production R nineT which sells in the States for $US12,995 and $22,49 in Australia.

Nmoto say it will take up to six months to make each Nostalgia to meet customers’ exact specifications.

Inspired Nostalgia

It is inspired by the legendary “unicorn” BMW R7 – the 1934 one-off prototype considered by many to be the Mona Lisa of motorcycles.

BMW R7 nostalgia
BMW R7

Nmoto founder Alexander Niznik says the Nostalgia consists of more than 96 handcrafted parts.

“It offers all the style of the original vintage model with all the peace-of-mind of the new model,” says .

Nmoto Nostalgia BMW R nineT
BMW R nineT and Nmoto Nostalgia

“It’s the perfect combination that makes a statement unlike anything else on the road.”

While it is based on the R Nine T with a 1170cc boxer engine with 81kW of power (110hp) and 86Nm of torque, Nmoto claim it is lighter and will top out at 225km/h.

Peak power and torque remain the same and they don’t say what they have done to make it 25km/h faster than the production model.Nmoto Nostalgia BMW R nineT

However, the power-to-weight ratio will be improved as it now weighs 205kg instead of 220kg. 

Even though it looks like it came from pre-WWII Bavaria, the Nmoto Nostalgia has a modern six-speed gearbox, traction control, anti-lock braking system and keyless ignition.Nmoto Nostalgia BMW R nineT

Unlike the original, it also features front and rear suspension!

The modern ignition lock and speedometer have been cleverly incorporated into the headlamp housing for that true nostalgia effect. 

It comes in 11 colour combinations, with customisation options that include adjustable steering, seat trim finish, luggage box and passenger seat.Nmoto Nostalgia BMW R nineT

 

Source: MotorbikeWriter.com